Thursday, June 22, 2017

The new Reny Mission Impossible is ready !

After 3 years of planning and building, the latest Allison V12 Mini Mod project of the Reny Mission Impossible Pulling Team from Duizel in the Netherlands is ready.
The Tractor was completely developed and built built by the RMI Team on Solid Works.
The new Reny Mission Impossible has a homemade 25CrMo4 tube frame with a homemade 25CrMo4 Rollcage, a homemade steering, a Domex sheet metal rear axle housing of Bennie Vreeman, self built whellie bars and homemade aluminium fenders. The drivers position on the new one is 300mm more forward, the center of gravity is lower and the Allison power plant sits 240mm more forward now than on the previous Reny Mission Impossible Mini Mod. The Team hopes to get a better balance with the Cepek tyres with those changes.
The Dutch Team purchased for the Mini a set of new Real Wheel aluminium rims with new Pioneer Giant Puller tyres from the USA.
The new rearend of the Mini Modified got a Ford 9" inch rear axle, a billet aluminium differential with a aluminuim center section, a special made ring and pinion gear, billet aluminium planetaries carrier housing with special made planetaries and new homemade brakes with Moto - Master components. Bennie Vreeman of Vreeman Special Products (VSP) have built the complete rear axle for the Team. The new ride also received VSP driveline, a 10´´ inch centrifugal clutch with 3 discs from Aadri van der Veeken (owner and driver of the New Holland Pro Stock Tractor called ,,Wickie Power´´) and a Trick Titanium clutch bellhousing. Because of the weight, the Tractor has no transmission, only a step-up planetaries gearbox with special made gears from Vreeman Special Products.
The new Reny Mission Impossible is powered by a supercharged Allison V12 V1710 Aircraft engine on methanol fuel. The power plant has a modified Allison stock engine block with modified Allison sleeves, revised Allison cylinder heads with revised camshafts, stock valves and special made springs, a lighter Allison crankshaft with stock bearings, Allison G6 rods and modified Allison pistons, a homemade air intake manifold with stock Allison parts, a Pro Charger F3 blower with a homemade air intake funnel and air filter, homemade titanium exhaust pipes, a dry sump lubrication, a homemade aluminium fuel and oil tank, a self built fuel system with a Hillborn methanol fuel pump and a homemade ignition with Mallory parts. Because of the weight, the cylinder banks of the Aircraft engine were milled down, the water jacket removed and the spark plugs exempted. The transmission on the front end of the Allison engine for the Pro Charger has a CNC milled aluminium housing with special made gears from Vreeman Special Products and special made driveshafts for the camshaft drive. The aluminium housing for the gearbox was milled by Bergmans Tools in Lommel, Belgium.
The Reny Mission Impossible Pulling Team around Rene Geerts will compete with their new 950kg Mini Modified in the NTTO Dutch Grand National Championship and in the Euro Cup this season.

for further information, check here: http://www.reny.nl/reny-lasertechniek/

The new Fully Loaded

The Fully Loaded Pulling Team from Dellroy, Ohio in the USA, together with Karlen Motorsports from Minvera, Ohio have built a new Component Super Stock Tractor during the last winter. The Super Stock got a completely new chrome-moly tube frame with a new Rollcage, a new hydraulic steering a Humpco billet rearend and a set of new Firestone Puller 2000 HP tyres with Midwest aluminium rims. The John Deere 8345R hood and fenders on the new chassis were took over of the old Fully Loaded Super Stock Tractor. The rearend has a Humpco billet aluminium center section with a billet aluminium differential, a special made ring and pinion gear and billet aluminium planetaries carrier housing with special made planetaries. Also the reverser and the driveline were built by Humpco Machine in the USA. The new ride got a 11´´ inch Crower centrifugal clutch with 5 discs, a aluminium flywheel and a Trick Titanium clutch bellhousing.
The drivers position on the new Karlen Motorsport Chassis is more forward and the center of gravity is lower than on his previous Chassis. The Team around Jeff Hothem hopes to get a better balance with those changes.
The new ride is powered by an 6 cylinder John Deere engine with 640cui. on methanol. The engine was completely built by Riverside Engine Inc. in Tiffin, Ohio. The engine has a JD stock block with a steel billet crankshaft, billet aluminium rods and pistons, a Riverside Engine Inc. aluminium cylinderhead with over head cam design, a 3 Holset HX 82 charger 2 Stage system from Blackbourn Racing Components, a MSD Pro Mag 44 ignition and a Racepak data logger.
The Team is absotlutly happy with their 1st and 3rd place finish at the Lucas Oil Pro Pulling League opener in Ansonia, Ohio. A great start for Jeff Hothem and his Team with the new Chassis into the new season.
The Fully Loaded Pulling Team will compete with their new Component Super Stock Tractor in the Lucas Pro Pulling League (Champions Tour) this year.

for further information, check here: https://fullyloadedpulling.com/

Baby Duck sold !


The Isotov TV2 powered Modified Tractor called ,,Baby Duck" of the Wuytack Family from Belgium was sold to a new owner in the Netherlands. The new owners of the Turbine powered Tractor is the Six Shooter Pulling Team around Corne Rombouts from Hoeven in the Netherlands.
The Six Shooter Pulling Team was many years active in the Super Stock class with an Case IH CVX 1190 on alcohol.
The Baby Duck Pulling Team was very successful with this Mod in the past. The Team won the 2003 European Championship title in 4.5t Modified class in Alahärma, Finland and European Championship title in the 3.5t Modified class in Lubersac, France in 2006.
The Six Shooter Pulling Team will compete with their new Toy in the Dutch Championship (Modified and Unlimited division) in the future.
Six Shooter Made (NL) 2013
Six Shooter Stroe (NL) 2015

Tuesday, June 20, 2017

Green Monster Mitas Edition @ Made NL 2017 by MrJo

Results

ETPC Euro Cup Made (NL) 2017, check at Results: http://tractorpulling.com/














NTTO GN Made (NL) 2017: https://www.ntto.nl/uitslagen/GN

NTPA GN Hutchinson, MN (USA) 2017 Session 1: http://ntpapull.com/pullresults/2017-HtchMN-01.htm

NTPA GN Hutchinson, MN (USA) 2017 Session 2: The session was cancelled due to inclement weather








PPL Champions Tour Mackville, WI (USA), June 16 ,2017: http://www.propulling.com/results/event-results/champions-tour-event-results/61-results/2017-results/2017-results-champions-tour/838-2017results-june-16-mackville-wi


PPL Champions Tour Mackville, WI (USA), June 17 ,2017: http://www.propulling.com/results/event-results/champions-tour-event-results/61-results/2017-results/2017-results-champions-tour/839-2017-results-june-17-mackville-wi

PPL Champions Tour Tampico, IN (USA), June 16, 2017: http://www.propulling.com/results/event-results/champions-tour-event-results/61-results/2017-results/2017-results-champions-tour/845-2017-results-june-16-tampico-in

PPL Champions Tour Tampico, IN (USA), June 17, 2017: http://www.propulling.com/results/event-results/champions-tour-event-results/61-results/2017-results/2017-results-champions-tour/843-2017-results-june-17-tampico-in

PPL Champions Tour Asonia, OH (USA), June 16, 2017: http://www.propulling.com/results/event-results/champions-tour-event-results/61-results/2017-results/2017-results-champions-tour/834-2017-results-june-16-ansonia-oh

PPL Champions Tour Asonia, OH (USA), June 17, 2017: http://www.propulling.com/results/event-results/champions-tour-event-results/61-results/2017-results/2017-results-champions-tour/837-2017-results-june-17-ansonia-oh

PPL Silver Series Asonia, OH (USA), June 16, 2017: http://www.propulling.com/results/event-results/silver-series-event-results/62-results/2017-results/2017-results-silver-series/835-2017-results-june-16-ansonia-oh

PPL Silver Series Asonia, OH (USA), June 17, 2017: http://www.propulling.com/results/event-results/silver-series-event-results/62-results/2017-results/2017-results-silver-series/836-2017-results-june-17-ansonia-oh

OTTPA Ravenna, NE (USA), June 16, 2017: http://outlawpulling.com/wp-content/uploads/2017/06/Ravenna-NE-1.pdf

OTTPA Ravenna, NE (USA), June 17, 2017: http://outlawpulling.com/wp-content/uploads/2017/06/Ravenna-NE-2.pdf

PPL 2017: Ohio State Benefit Pull - Friday Winner

Blower Power Made 2017

Team Lambada - Tractor Pulling Eurocup & GN Made's Powerweekend 2017

Monday, June 19, 2017

Photos Made's Powerweekend 2017 - by Jan Lo --janwerners Pulling-Bilder--

Saturday



--------------------------

Sunday



------------------------

Photos by Jan Lo --janwerners Pulling-Bilder--
All my photos without effects or cutting! All photos are original! 
Photos are not in high resolution! 
You want to use some photos for your facebook- or your website? 
Write a mail to: janloo1407@gmail.com

Friday, June 16, 2017

This Weekend !

https://www.powerweekend.nl/nl/

http://www.powerpullnationals.com/

http://ohiostatepull.com/

http://www.mackvillenationals.com/

https://www.facebook.com/tampicotractorpull/

The new Green Molli

Kaiser Performance and the Kaiser Pulling Team around Super Stock driver Marcus Kaiser from Gussenstadt in Germany have finished their John Deere 3.5t Sport class costumer project. After 2 1/2 years of planning and building the new Tractor was ready in the mid of May and made his maiden run on the Pulling track in Holzheim, Germany a few days later. The new John Deere got the name ,,Green Molli´´ and received a great design by Steffen Schaab on the side shields.
The new vehicle got a homemade steel tube frame with a homemade steel Rollcage, a hydraulic steering, a homemade adaption with seperate oil pump for brake and steering system, a original John Deere 4230 sheet metal hood, homemade sheet metal fenders, a JD 4230 rearend and Fendt steel rims with cut 38" inch Goodyear tyres.
The tube frame and the ROP come from the Alky burner Super Stock called ,,Second Chance´´, who blew up in a big fireball in Füchtorf (D) 2011. The stock rearend has a JD ring and pinion gear with a JD 4230 stock differential. The gearbox of the Sport class Tractor also comes out of an JD 4230 and has original gears in it. The gearbox was overworked for only two different ratios (2 forward and 1 reverse). The Tractor also has a 11" inch Van der Waal centrifugal clutch with 3 discs (used parts of Team Kaiser -reworked as Sport application, different clutch fingers, Springs and weights), a billet
made KP Performance flywheel, a homemade KP clutchliner (milled clutchhouse for best fit of liner) and a KP standard product mainshaft (clutch to gearbox). With the KP clutch liner, the new ride can drive without shratter blankets around the JD stock clutch bellhousing.
The new Green Molli is powered by a 6 cylinder John Deere engine with 6.6l capacity on diesel fuel.
The engine has a JD 4230 stock block with new orginal sleeves, a JD 40 series head with standard valves and springs, a original camshaft, a stock JD crank with new original rods and pistons, a Holset HX 55 turbocharger, a newly made Kaiser Performance style prototype aluminium intake manifold, a homemade steel exhaust manifold, a Bosch Diesel fuel pump with 10mm elements from Lindemann Dieseltechnik, a homemade fuel tank, a original JD oil pump, a Voltkraft K204 4-Channel datalogger, a MAN heatexchanger (Intercooler) with 2 section air water and a homemade 45l extra water tank for cold water.
The new Tractor is equipped with lot´s of KP stuff a lot of other customer also run such as, clutch setup, clutch liner, turbo - killswitch unit, driveshaft, hitch assembly for original (non overworked) JD rearends, clutch thrust setup for JD OEM clutchhousing, rollcage assembling kit, intake and exhaust mainifolds,....
Main thing is, that the customer (a Familiy of four) wants to step into pulling with a reliable JD Tractor on solid level. They decided together with the customer, to build up a very basic motorized Tractor on standard components to keep the budget. Beside it was the goal to get another nice looking JD into the German Sport Class series. The basic idea was to built a Tractor that can be upgraded over the next years (if the customer wants so) without changing a lot on the look, chassis, and safety equipment.
The owner of the Tractor Stefan Moll will compete in the German Championship this year.

Team Kaiser and Kaiser Performance wants to thank their customers all over Europe for their trust in KP products. Kepp on Pulling and stay tuned!!!

for further information, check here: https://www.pullingteamkaiser.de/

or check here: https://www.facebook.com/Kaiser-Performance-309375439200587/?ref=ts 

more pics of the Tractor, check here: https://goo.gl/photos/6cL5tceYS9gPpQAaA 




The new Resistance 3.6t Super Sport

The new 3.6t Valtra Super Sport Tractor called ,,Resistance" from Buurse in the Netherlands is ready. The Team around Martin Mogezomp and Maikel de Jong have built on the new Tractor around 2 years in their workshop in Buurse.
The Valtra Tractor got a homemade Domex wedge frame with a homemade steel ROP, a Valtra 8150 rearend with a needle bearing diff, a Valtra transmission with 4 gears, Valtra N Series fenders and a Valtra S280 hood. The transmission of the new Tractor comes out of the old dutch Pro Stock Tractor called ,,Next Sensation" from Jurian Duijn. The Vehicle has new Eagle centrifugal clutch with 4 discs from Finland. The Tractor also received a set of used steel rims with cut Goodyear 650 x 38 rear tyres.
The new Resistance is powered by an 6 cylinder Sisu Diesel engine with 6.9l capacity. The engine have a Sisu 620 stock block with stock sleeves, a revised Sisu 620 cylinder head with a grinded camshaft, a stock crankshaft with Sisu rods and pistons, a homemade intake and exhaust manifold, a billet Holset HX60 turbocharger, a homemade aluminium intercooler and a Bosch 12 cylinder P diesel fuel injection pump with 13mm elements.
The Team was satisfied with their first hooks so far in front of the sledge this year.
The Resistance Pulling Team will compete with their new 3.6t Super Sport Tractor in the NTTO Dutch Championship, in the Dutch TSTA competition and on some German Championship rounds this year.